SAFETY

SCCA TIME TRIALS SAFETY RULES

CLICK HERE FOR TEXT VERSION OF SAFETY RULES

While the SCCA Time Trials Program is focused on creating access to on-track competition and having fun, safety is something we take very seriously.  It is always recommended that participants prepare their vehicle and utilize driver safety gear that meets the Safety Level 3 standard.  However, some events and programs (including the Time Trials National Program) do allow participation at Safety Levels 1 and 2. 

When you enter an event, event information - sometimes called the Supplementary Regulations - should specify the minimum level of safety for you and your car. You can use this page to find out what is required at each safety level.

1. Safety Level 1

A. All vehicles must provide factory original (or better) seats that are securely mounted.

B. All vehicles must have seat belts with a minimum of three (3) mounting points mounted in accordance with manufacturers’ recommendations when applicable (SFI or FIA rated are recommended).

C. When in-car coaches are utilized, any seat and restraints used by the coach shall match or exceed those used by the driver.

A. The interior and trunk must be emptied and clear of all loose items, including floor mats which are not secured with clips or fasteners.

A. Brake pads or shoes should not be more than 50% worn at the start of an event and should not ever be more than 85% worn during competition.

B. Brake fluid must be clean and full (DOT 4 recommended).

C. Vehicles must have at least one working brake light.

D. There must be no brake fluid leaks.

E. Rotors and drums must be in good condition without cracks or discoloration.

A. Tires must be in good condition with adequate tread and speed rating.

B. All lug nuts, wheel bolts or wheel nuts must be present and torqued to spec.

C. Hub caps, or any wheel cosmetic accessory which is not positively secured by clip or fastener, must be removed.

D. Wheels must not have cracks or structural damage.

A. Wheel bearings must not have play.

B. Ball joints must be in good condition.

C. Steering must not have excessive play.

D. Shocks/Struts must not be leaking.

A. All fluids must be at correct levels. Fluid caps must be tight and secure, overflow containers present and there must not be any fluid leaks.

B. Belts and hoses must be in good condition.

C. Battery must be secured, and battery terminals covered. (Note: flexible battery hold-downs, such as bungee cords/straps, are not acceptable.)

D. Exhaust system must be functional. (There may be sound restrictions.)

E. Throttle must have a quick, positive return.

A. When present, any roll bar must be properly installed and securely attached.

B. When present, any part of a roll bar able to be contacted by a driver’s head must have padding.

A. Glass must not have any severe cracks.

B. A rear-view device must be present, and any rear-view mirrors must be secure and free of cracks.

C. Any video cameras/recording devices must be securely mounted.

It is highly recommended that all convertible vehicles be equipped with an aftermarket roll bar that meets or exceeds the standards set in the Time Trials Safety Standard Level 2 (see below). However, minimum safety standards requires the vehicle meets at least one of the following criteria and is not subject to any of the listed exceptions:

1. Convertible vehicles up to and including the 2005 model year must have rollover protection meeting one of the following criteria:

A. The vehicle is equipped with documented factory installed roll over protection. (Examples of manufacturer-documented roll over protection include hydroformed and reinforced a-pillars or windshield frame and factory installed roll bars and/or “pop-up” bars that are designated as roll over protection.)

B. The vehicle is equipped with a commercially produced roll bar or roll cage which is described by the manufacturer to provide track-appropriate rollover protection. (E.g., “style” bars are not acceptable.)

1. Braces and portions of the main hoop subject to contact by the driver’s or passenger’s helmet, as seated normally and restrained by seatbelt and harness, must be padded with a non-resilient material such as Ethafoam® or Ensolite® or other similar material with a minimum thickness of 1/2 inch. Padding meeting SFI spec 45.1 or FIA 8857-2001 is strongly recommended.

C. The vehicle is equipped with a roll bar that meets the Safety Level 2 standards for material and construction.

2. Convertible vehicles of the 2006 model year or later must have a roll bar that meets the Safety Level 2 standards for material and construction unless one of the following criteria is met.

A. The vehicle is equipped with documented factory-installed roll over protection or a commercially produced roll bar or roll cage which is described by the manufacturer to provide track-appropriate rollover protection.

B. The vehicle is six (6) cylinders, with the OE drivetrain and may only be naturally aspirated.

C. The vehicle is four (4) cylinders or less, with the OE drivetrain, including any forced-induction equipment.

Note: This means that for 2006+ vehicles, if the engine is not the original equipment model as delivered in that vehicle, aftermarket forced induction has been installed, or the vehicle has more than six (6) cylinders or six (6) cylinders and forced induction of any type, the vehicle must have aftermarket rollover protection or documented factory rollover protection.

3. T-tops and targa top cars:
T-top and targa top cars are not considered convertibles, and do not fall under the convertible requirements.

A. Helmets meeting at least one of the following standards must be worn while on track:

1. All helmets meeting the latest or two immediately preceding Snell Founda­tion standards (SA2020, M2020, EA2016, SA2015, SA2010, SAH2010, M2015, M2010)

2. SFI standards 31.1/2010, 31.1/2015, 31.1/2020, 41.1/2010, 41.1/2015, 41.1/2020

3. FIA standards 8859-2020, 8860-2018, 8860-2018-ABP, 8859-2015, 8860-2010;

B. Full face shall be worn in open vehicles without windshields (E.g., formula car, sports racer, exoskeleton kit-cars). A face shield, goggles, or similar face protection (conventional eyeglasses are not sufficient) shall be worn while competing in any other vehicle with less than the standard-size windshield.

C. For maximum protection, helmets must fit securely and should provide adequate peripheral vision. The chin strap must be securely fastened.

A. Shoes covering the entire foot shall be worn.

2. Safety Level 2

Safety Level 2 generally means an appropriate racing-specific seat, 4-point roll bar, 5-point racing harness, arm restraints or window net, and fire-retardant helmets and clothing.

All vehicles required to meet Safety Level 2 Standards must meet the Safety Level 1 Standards, plus the additions below.

These specifications apply to all vehicles (other than those issued an SCCA Logbook before 1/1/19). Cars issued an SCCA Logbook before 1/1/19 may continue to compete with their previously approved rollover structure or comply with the following specifications.

A roll bar is defined as a main hoop and diagonal placed behind the driver and supplemented by two braces. The roll bar must be designed to withstand compression forces resulting from the weight of the car coming down on the roll structure, and to take fore-and-aft loads resulting from the car skidding along the ground on the roll structure. The basic purpose of the roll bar is to protect the driver in case the vehicle rolls over. Roll bars must meet the following criteria:

A. One continuous length of tubing must be used for the hoop member with smooth continuous bends and no evidence of crimping or wall failure.

B. The top of the roll bar must be above the top of the driver’s helmet when the driver is in normal driving position.

C. The two (2) vertical members forming the sides of the hoop must be more than 15 inches apart (inside dimension), and it is desirable that it extend the full width of the cockpit.

D. An inspection hole of at least 3/16 inch diameter to facilitate verification of wall thickness may be required. It must be drilled in a non-critical area of a roll bar member at least three inches from any weld or bend.

E. All bolts and nuts shall be SAE Grade 5 or better, 5/16-inch minimum diameter.

F. Braces and portions of the main hoop subject to contact by the driver’s or passenger’s helmet, as seated normally and restrained by seatbelt and harness, must be padded with a non-resilient material such as Ethafoam® or Ensolite® or other similar material with a minimum thickness of 1/2 inch. Padding meeting SFI spec 45.1 or FIA 8857-2001 is strongly recommended.

G. The size of tubing to be used for the main hoop, braces and diagonals shall be determined on the basis of the weight of the car. The following minimum sizes are required and are based upon the weight of the car without the driver. Dimensions are nominal; 0.010-inch variation in wall thickness is allowed.

Vehicle Weight
(Without driver)

Tubing Size (inches)
(outer diameter x wall thickness)

Up to 1,500 lbs.

1.25 x 0.090

1,501–1,700 lbs.

1.375 x 0.080

1,701–2,699 lbs.

1.500 x 0.095

1.625 x 0.080

2,700 lbs. and up

1.500 x 0.120

1.750 x 0.095

2.000 x 0.080

H. The roll bar hoop and all braces must be of seamless or DOM mild steel tubing (SAE 1010, 1020, 1025) or equivalent, or alloy steel tubing (SAE 4130). For cars logbooked before 1/1/16, existing ERW tubing is acceptable.

I. All welding should be of the highest possible quality with full penetration. Craters should be filled to the cross section of the weld and undercut should be no more than 0.01 inch deep.

J. All roll bars must be braced in a manner to prevent movement in a fore-and-aft direction with the braces attached within the top third of the roll hoop. At a minimum, two (2) braces must be used, parallel to the sides of the car, and placed at the outer extremities of the roll bar hoop. Such braces should extend to the rear whenever possible. Diagonal lateral bracing must be installed to prevent lateral distortion of the hoop. In most cases, a lateral brace from the bottom corner of the hoop on the side to the top corner of the hoop on the other side is sufficient. Although installing the diagonal lateral brace in the main hoop is the strongest alternative (and hence most preferable), there may be instances where such an installation is not practical. In such situations, the installation of the diagonal brace running from the bottom of the fore/aft brace on one side to the top corner of the hoop on the other side is acceptable. In convertible vehicles with a production line beginning 1990 or later, such as the Mazda Miata, a “V” design, also known as a “double diagonal” used between the rear supports is acceptable.

K. Removable roll bars and braces must be very carefully designed and constructed to be at least as strong as a permanent installation. If one (1) tube fits inside another tube to facilitate removal, the removable portion must fit tightly and must bottom on the permanent mounting, and at least two (2) bolts must be used to secure each telescope section. The telescope section must be at least eight inches in length. One (1) bolt is required if one (1) end is welded to the main hoop.

L. Roll bars and braces must be attached to the frame of the car wherever possible. Mounting plates may be used for this purpose where desired.

M. In the case of cars with unitized or frameless construction, mounting plates may be used to secure the roll bar structure to the car floor. The important consideration is that the load be distributed over as large an area as possible. A backing plate of equal size and thickness must be used on the opposite side of the panel with the plates through-bolted together.

N. Mounting plates bolted to the structure shall not be less than 0.1875 inch thick and the use of a back-up plate of equal size and thickness on the opposite side of the panel with the plates through-bolted together is recommended. A minimum of three (3) bolts per plate is required for bolted mounting plates.

O. Mounting plates welded to the structure shall not be less than 0.080 inch thick. Whenever possible, the mounting plate should extend onto a vertical section of the structure, such as a door pillar.

Seats must a one-piece, bucket-type race seat, be securely mounted and provide fore/aft and lateral support. Seats must accommodate, with appropriate routing, 5 (or more) point safety belts including sub-strap. OE seats may not be modified to accommodate belts, aftermarket seats must be installed per manufacture guidelines.

A. All drivers shall utilize either a 5-, 6- or 7-point restraint harness.

B. The following harness requirements must be met:

1. Shoulder straps shall be separate.

2. Two inch shoulder straps shall only be used with head and neck devices.

3. All harnesses shall bear labels bearing either of the following SFI or FIA certifications:

a. SFI specification 16.1 or 16.

b. FIA specification 8853/1985 including amendment 1/92 or FIA specifications 8853/98 and 8854/98.

4. Harnesses shall be in good condition (no cuts, abrasions, abnormal wear, etc.). It is highly recommended that harnesses are not utilized past their expiration date.

5. The following steps shall be taken when threading harness through a harness bar

a. Figure 1

b. Figure 2

c. Figure 3

d. Figure 4

e. Figure 5

f. Figure 6

A. All vehicles shall have a device (such as a fire bottle/fire extinguisher/fire suppression system) securely mounted with metal mounting brackets of the quick-release type within reach of the driver to suppress fires.

The device should meet at least one of the following minimum requirements:

1. On-board fire systems per SCCA Road Racing General Competition Rules (GCR).

2. Halon 1301 or 1211, 2 pound minimum capacity by weight.

3. Dry chemical, 2 pound minimum with a positive indicator showing charge. Chemical: 10 BC or 1A10BC Underwriters Laboratory rating.

1. For Safety Level 2, helmets meeting one of the following standards are acceptable and must be worn while on course:

A. Snell Foundation Standards with Snell sticker 2015 or later for Special Application (SA2020, EA2016, SA2015).

B. SFI standards 31.1/2015, 31.1/2020

C. FIA standards 8859-2015, 8860-2010 or newer.

2. For drivers of any vehicle without a DOT-approved windshield (such as kit-cars, Sports Racers, Formula Cars and Specials) or any other vehicle with less than standard-sized windshield, helmets meeting these additional criteria are required:

A. Helmets must be full face.

B. A shield, preferably made of impact-resistant materials, shall be used while on course (conventional eyeglasses are not sufficient).

1. Driving suits shall meet one of the following standards:

A. FIA standards (8856 -1986, 8856-2000 or 8856-2018).

B. SFI 3-2A/5 or higher (e.g., /10, /15, /20) certification.

C. Suits carrying SFI 3-2A/1 certification may be worn only with fire resistant underwear.

D. Gloves made of leather and/or accepted fire-resistant material containing no holes.

E. Socks made of accepted fire-resistant material.

F. Face coverings (balaclavas) of accepted fire-resistant material for drivers with beards or mustaches.

G. Shoes, with uppers of leather and/or nonflammable material that, at a minimum, cover the instep

1. For drivers of any vehicle where the compatibility of belts and seats meet the use of head and neck support systems, the use of a head and neck support system is highly recommended.

2. For a track-based event (Time Attack/TrackSprint) a driver’s-side window safety net or arm restraints are highly recommended for all cars.

3. For a HillClimb event, arm restraints are required in any open car and a window net or arm restraints are required for closed cars.

3. Safety Level 3

It is intended that Safety Level 3 be similar to that of SCCA Road Racing. Vehicles of motorsports-specific construction are required to meet these specifications. For National Time Trial Events, vehicles prepared beyond Max Category Rules and competing on tires without DOT-Approval must meet Safety Level 3 Standards.

All Safety Level 3 vehicles must meet the requirements of Safety Levels 1 and 2, plus the inclusion of a roll cage compliant with specifications listed here. A roll cage consists of the main hoop, front hoop, side protection, and braces as specified in these Rules.

These specifications apply to all vehicles other than those issued an SCCA Logbook before 1/1/19. Cars issued an SCCA Logbook before 1/1/19 may continue to compete with their previously approved rollover structure or comply with the following specifications.

Please see SCCA General Competition Rules section 9.4 for diagrams and illustrations.

The main hoop (behind the driver) must be the full width of the cockpit for all cars. It must be one continuous length of tubing with smooth bends and no evidence of crimping or wall failure. The main hoop must maintain a single plane.

A. On all closed cars, the main hoop must be as close as possible to the roof and “B” pillars.

B. On open cars retaining the windshield frame, the main hoop must be full height for the entire width of the hoop. The top of the main hoop must be at least 2 inches above the driver’s helmet.

C. Open cars without the windshield frame may use an asymmetric main hoop. The main hoop must be full width to the passenger side of the car. On the passenger side of the car, the hoop must be at least as high as the top of the rear corner of the door. The main hoop must be high enough that a straight line drawn from the top of the main hoop to the top of the front hoop would pass over the driver’s helmet and steering wheel when the driver is seated in the normal driving position. Additionally, the top of the main hoop must be at least 2 inches above the driver’s helmet.

A. Main hoops shall incorporate a diagonal brace. The brace shall either be in the plane of the main hoop or extend from the top of one rear brace to the bottom of the opposite rear brace. Automobiles with mid-mounted engines can have the lower mounting point attach to the frame of the automobile within 6 inches of the main hoop. In the case of braces in the plane of the main hoop, the brace must span at least 50% of the width of the main hoop, and at least 75% of the height of the main hoop. In convertible vehicles with a production line beginning 1990 or later, such as the Mazda Miata, a “V” design, also known as a “double diagonal” used between the rear supports is acceptable.

B. Cars must incorporate a main hoop horizontal brace at the approximate level of the driver’s shoulders but not lower than the shoulder belt mounting point as described. If a double-diagonal “X” brace is used in the plane of the main hoop, a half-width horizontal brace may be used behind the driver’s seat to mount the seat back and shoulder harness.

C. Cars must have two (2) braces extending to the rear from the main hoop and attaching to the frame or chassis. Braces must be attached as near as possible to the top of the main hoop (not more than 6 inches below the top), and at an included angle of at least 30 degrees.

D. Open cars must have two (2) braces extending forward from the main hoop and attaching to the front hoop, not more than 6 inches below the top of the front and main hoop. It is recommended that the front and rear braces attach to the main hoop as close as possible to each other.

E. On cars where the rear window/bulkhead prohibits the installation of rear braces (e.g., Honda del Sol), the main hoop shall be attached to the body by plates welded to the cage and bolted to the stock shoulder harness mounting points. This installation design must incorporate a diagonal bar connecting the top of the main hoop to the lower front passenger side mounting point (Petty bar). Alternatively, the rear window may be removed and a clear, LEXAN™ replacement installed. The rear cage braces may pass through this replacement window and through the engine cover or bodywork to allow connection to the frame or unibody.

A. Roll cages may be of two designs, low front hoop or high front hoop. All closed-top cars and cars that retain the windshield frame must have a high front hoop design. Open cars may incorporate a high or low front hoop design. High front hoops are also referred to as side hoops.

1. Closed cars: The front hoop (side hoop) must follow the line of the A-pillars to the top of the windshield and be connected by horizontal bars to the top of the main hoop on each side (as close to the roof as possible). Instead of a single front hoop, two side hoops (down tubes) may be used. Alternatively, a top “halo” hoop following the roof line from the main hoop to the windshield with forward down tubes following the A-pillars to the floor may be used. Regardless of which one of the two approved tubing configurations, there shall be a tube connecting the two A-pillar tubes at the top of the windshield.

2. Open cars: The height of the front hoop must be consistent across the full width of the cockpit.

B. Front Hoop Bracing
All open cars with a high front hoop and all tube frame closed cars must incorporate a horizontal front hoop brace at the approximate level of the dashboard. It is recommended production-chassis cars also have the front hoop brace.

1. Tube(s) may extend, from each front down tube, forward to the firewall. For Unlimited or SCCA GCR-class cars which allow it, tube(s) may extend through the firewall. In this case it is recommended this tube, one on each side, connect to the chassis at a point not more than 12 inches forward of the front axle centerline.

A. Side tubes connecting the front and main hoops across both door openings are strongly recommended. Tubes that are welded to any part of the same mounting plate are considered to be connected to one another.

B. NASCAR-style side protection or one bar bisecting another to form an “X” is permitted. Door side tubes may extend into the front door.

1. Door window glass, window operating mechanism, inner door trim panel, armrest, map pockets, wiring harnesses for door locks, windows, power mirrors, seat wiring, etc., and inside door latch/lock operating mechanism may be removed and the inner door structural panel may be modified.

2. The stock outside door latch/lock operating mechanism shall not be removed or modified unless specifically authorized in the Rules.

A. Production-chassis cars: The roll cage must attach to the vehicle structure within the passenger compartment in a minimum of six (6) points as specified in these Rules.

B. Tube-frame cars: The roll cage shall be integrated into the frame or chassis.

C. Mounting Plates

1. Mounting plates welded to the structure of the car shall not be less than 0.080 inches thick and no more than 0.25 inch thick. Plates may be on multiple planes.

2. The thickness of mounting plates bolted or riveted to the structure of the car must not be less than the thickness of the roll hoop or brace that they attach to the chassis and must be backed up with a plate of equal size and thickness on the opposite side of the chassis panel. Plates may be on multiple planes but shall not be greater than 15 inches on any side.

3. Fasteners for bolted or riveted mounting plates must be Grade 5/Metric 8.8 or better with a minimum diameter of 5/16 inch.

A. Seamless or DOM mild steel tubing (SAE 1020 or 1025 recommended) or alloy steel tubing (SAE 4130 or T45), or Docol R8 tubing must be used for all roll cage structures. Alloy and mild steel tubing may not be mixed. ERW tubing is not allowed.

B. The following table shows the minimum allowed tubing outer diameter and wall thickness by vehicle weight:

 

Vehicle Weight
 (not including driver)

Tubing Size (inches)
(outer diameter x wall thickness)

Up to 1,000 lbs.

1.00 x 0.060

1,001– Up to 1,500 lbs.

1.25 x 0.090

1,501–1,700 lbs.

1.375 x 0.080

1,701–2,699 lbs.

1.500 x 0.095

1.625 x 0.080

2,700 lbs. and up

1.500 x 0.120

1.750 x 0.095

2.000 x 0.080

C. For purposes of determining tubing sizes, the vehicle weight is as raced without driver, fuel and ballast. The minus tolerance for wall thickness should not be less than 0.010 inch below the nominal thickness.

D. The required tubing elements must meet the material minimums set forth above. Optional tubing elements may be any size.

E. The minus variance of tubing wall thickness due to manufacturing tolerances is limited to 0.010 inch.

F. Either an inspection hole between 3/16- and 1/4-inch diameter must be drilled in a non-critical area of the front and rear hoops, as well as one of the supplemental braces to facilitate verification of wall thickness; or alternatively, wall thickness may be determined by non-invasive means and noted in the logbook and inspected by such means.

A. All portions of the roll cage subject to contact by the driver must be padded with a minimum 1 inch of material. Padding that meets or exceeds SFI 45.1 or FIA 8857-2001 (curved padding), or SFI 45.2 or FIA sports car head rest material (flat padding) specification is recommended.

B. No portion of the roll cage may have an aerodynamic effect by creating a vertical force.

C. The radius of all bends in the roll cage (measured at centerline of tubing) must not be less than three times the diameter of the tubing.

D. It is recommended that all joints of the roll cage be welded. All welding must include full penetration, no cold lap, no surface porosity, no crater porosity, no cracks, no whiskers, and so forth. Welds shall be continuous around the entire tubular structure. Procedures for welding alloy steel shall be in accordance with accepted industry practice. It is recommended that a certified AWS D1.1 welder do all welding.

E. It is recommended that gussets be used at all joints.

F. Any number of additional tube elements is permitted within the boundaries of the cage structure. Such tube elements may pass through any mandatory or optional bulkhead or panel separating the driver/passenger compartment from the trunk/cargo area/fuel tank/fuel cell area provided the bulkhead is sealed around such tube elements.

G. Removable roll cage bracing is acceptable in one of the following configurations.

1. If one tube fits inside another tube to facilitate removal, the removable portion must fit tightly and must bottom by design, and at least two (2) bolts must be used to secure each joint. The telescoping section must be at least 8 inches long. The minimum bolt diameter is 3/8 inch.

2. Removable bracing may incorporate connectors of the double-lug, double ear-type, tapered or muff-type. The double-lug type must include a doubler, gusset, or capping arrangement to avoid distortion or excessive strain caused by welding. Double ear-type joints must be fully welded at all the mating surfaces.

A. Cars may compete with FIA or FIA-Approved Test Houses homologated cages provided the cage was built by the manufacturer or a manufacturer designated shop/team and approved for use. Cars must have the FIA identification plate attached to the cage along with a letter from SCCA Technical Services certifying the origins of the car, or confirmation that the cage was certified by an FIA-Approved Test House.

B. Cars may compete with an approved MSA (Motor Sports Association UK) Roll Over Protection System Certificate. All related engineering drawings and documents shall be submitted to SCCA Technical Services. Cars must have MSA identification plate attached to the cage along with a letter from SCCA Technical Services certifying the cage was approved by the MSA.

C. Cars which do not comply with the design criteria set forth for roll hoops must have a waiver/homologation certificate issued by the Road Racing Technical Staff. Cars which are excepted from the published design criteria, shall at all times have available for examination a current logbook, a copy of the letter of exception from the Road Racing department and supporting engineering documentation. Cars which have previously been issued homologation Certificates may satisfy this rule by presentation of said certificate or a copy. Vehicles with an SCCA logbook issued before  prior to January 1, 1983 do not require homologation certificates.

Note: This line primarily applies to those who own older SCCA road racing cars or factory-built racecars that probably had a previous history with the SCCA or other sanctioning body. While the Road Racing Technical Staff can evaluate and approve another design, the far easier (and less expensive path) here is to build it to the published specs. If you have an older formula car or sports racer, it should have a homologation certificate that goes with it.

1. For Safety Level 2, helmets meeting one of the following standards are acceptable and must be worn while on course:

A. Snell Foundation Standards with Snell sticker 2015 or later for Special Application (SA2020, EA2016, SA2015).

B. SFI standards 31.1/2015, 31.1/2020

C. FIA standards 8859-2015, 8860-2010 or newer.

2. For drivers of any vehicle without a DOT-approved windshield (such as kit-cars, Sports Racers, Formula Cars and Specials) or any other vehicle with less than standard-sized windshield, helmets meeting these additional criteria are required:

A. Helmets must be full face.

B. A shield, preferably made of impact-resistant materials, shall be used while on course (conventional eyeglasses are not sufficient).

1. Driving suits shall meet one of the following standards:

A. FIA standards (8856 -1986, 8856-2000 or 8856-2018).

B. SFI 3-2A/5 or higher (e.g., /10, /15, /20) certification.

C. Suits carrying SFI 3-2A/1 certification may be worn only with fire resistant underwear.

D. Gloves made of leather and/or accepted fire-resistant material containing no holes.

E. Socks made of accepted fire-resistant material.

F. Face coverings (balaclavas) of accepted fire-resistant material for drivers with beards or mustaches.

G. Shoes, with uppers of leather and/or nonflammable material that, at a minimum, cover the instep

1. For drivers of any vehicle where the compatibility of belts and seats meet the use of head and neck support systems, the use of a head and neck support system is highly recommended.

2. For a track-based event (Time Attack/TrackSprint) a driver’s-side window safety net or arm restraints are highly recommended for all cars.

3. For a HillClimb event, arm restraints are required in any open car and a window net or arm restraints are required for closed cars.

4. Alternate Accepted Logbooks

When upper Safety Levels are required, vehicles from approved vintage groups and alternate sanctioning bodies may participate in SCCA Time Trials as long as they meet the rules for their respective groups and have been issued a logbook from an accepted group. The burden of proof for safety standards for each vehicle running under this allowance falls on the driver.

A. National Auto Sport Association (NASA)

B. BMW Car Club of America (BMWCCA)

C. Porsche Club of America (PCA)

D. Porsche Owners Club (POC)

Note: At Time Trials National events, the roll bar/roll cage minimums for DOT and non-DOT tires must be met.

A. Sports Car Club of America (SCCA)

B. Classic SportsCar Racing Group (CSRG)

C. Society of Vintage Racing Enthusiasts (SOVREN)

D. Sportscar Vintage Racing Association (SVRA)

E. Vintage Auto Racing Association (VARA)

F. Vintage Motorsports Council (VMC)

G. Vintage Drivers Club of America (VDCA)

H. Historic Sportscar Racing (HSR)

I. American IndyCar Series (AIS)

5. VEHICLE AND DRIVER GEAR SAFETY INSPECTION

Vehicles must be inspected to participate in SCCA Time Trials and the official tech form must be filled out, signed by the driver and turned in to the designated event official(s). The driver is responsible for ensuring that the vehicle being used is properly prepared for operation under elevated acceleration, braking and cornering forces.

1. Whenever the following items are installed on a vehicle, an SCCA Tech Inspector must evaluate the installation:

A. Any aftermarket safety item required by SCCA Rules.

B. Aftermarket seat(s).

C. Aftermarket seat belts/racing harnesses.

D. Roll bar or roll cage.

2. Inspection Requirements
Items must be inspected for secure installation and proper fasteners (e.g., sandwich plates on bolt-in roll bars/cages). The driver is responsible for the installation being compliant with manufacturer guidelines, and adequate material (e.g., tubing size and thickness) but inspectors should be on the lookout for obvious inappropriate installation or improper material.

3. Required Driver Gear Safety Inspection
The following driver gear safety items must be inspected by an SCCA Official. A vehicle shall not get approval to go on track until gear for the driver(s) of that car has been checked.

A. Helmets must be inspected, and a tech sticker should be affixed so that officials can easily check that the helmet has been inspected and approved. Helmet stickers may be annual.

B. Any required driver gear item must be inspected by an SCCA Tech Inspector.

4. Logbooks/Annual Inspections

A. Vehicles may be annually inspected, and that inspection may be noted with proof of inspection (e.g., sticker, card or logbook).

B. A vehicle with an annual tech is not required to be inspected at an event, but the driver shall still turn in a completed tech form.

C. Any change or addition to aftermarket safety equipment requires a re-inspection, even if that vehicle is within the annual inspection period.

D. SCCA Road Racing Annual Inspections may be honored and a Road Racing vehicle with an annual tech is not required to be inspected at an event, but the driver shall still turn in a completed tech form.

Motorsports are inherently dangerous. These Rules are in no way a guarantee against injury or death to participants, spectators or others. You can reduce risk by driving well, properly using superior safety gear, paying attention, and reporting unsatisfactory issues to the event officials. Drivers are responsible for ensuring that the vehicle being used is properly prepared for operation under elevated acceleration, braking and cornering forces. Drivers must have a Technical Inspection (Tech) Sheet completed and available to present to an SCCA Official.